Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Parker
Electric gate repair in Parker, TX usually comes down to a post that moved, a motor that overheated, or a control board that stopped talking to the remote. Most Parker calls we take are for swing gates that drag after the expansive clay under the post shifts, or operators that stall after a storm. We get to Parker fast, diagnose the actual fault, and fix the gate without swapping parts that don’t need swapping. Call (877) 265-5743 for a free estimate on Electric Gate Repair.
Why Pinehurst Gate Repair Is Parker’s Preferred Electric Gate Repair Company
Parker isn’t a city of standard builder gates. The subdivisions off Country Club Road and along Parker Road are custom, gated, and built on some of the most reactive clay in Collin County. That means gate problems here don’t look like gate problems elsewhere. A FAAC swing operator that trips mid-cycle is rarely failing on its own; it’s fighting a post that heaved half an inch out of plumb. We read the whole system, not just the box on the slab.
We’re gate specialists. Not a fence company with a gate crew on the side. We work on the brand you already have. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, Mighty Mule. If it opens and closes, we know the wiring. Parker homeowners call us because they’ve already tried the guy who “does a little of everything,” and the gate still stalls at 40 degrees. We fix it once.
Our techs are on the road to Parker from Rowlett regularly, and we know how to get to the gated enclaves and private drives without wandering. When you call, you’ll talk to someone who understands that a gate stuck open on a multi-acre lot isn’t a convenience issue. It’s a security and liability issue.
Styles & brands we work with
Electric Gate Motor in Parker
An Electric Gate Motor in Parker takes real abuse. Summer heat pushes motors past their thermal limit, and when a swing gate drags because the hinge post moved in clay, the motor strains against the bind until it burns out. We replace motors on LiftMaster, FAAC, BFT, and Linear swing and slide operators, and we check the gate’s mechanical alignment first so the new motor doesn’t inherit the same death sentence. In Parker, a motor replacement on a residential swing gate typically runs $450 – $900 depending on operator class and whether the arm or ram needs replacing too.
Motor Diagnosis and Replacement
We bench-test the old motor, verify voltage at the board, and confirm the capacitor isn’t the real culprit before recommending a swap. You’ll see the failed part and understand why it failed. Then we install the correct motor, set the limits, and re-tune the force settings for the gate’s actual weight.
Strain Prevention From Misaligned Posts
Before installing a motor in Parker, we check hinge-post plumb and gate sag. A motor replaced behind a dragging gate is a motor you’ll replace again in two years. We correct the mechanical issues first, then power the gate back up and let it cycle clean.
Gate Access Control in Parker
Gate Access Control in Parker usually means keypads, remotes, loop detectors, and intercom or telephone-entry modules on automatic driveway gates. The problem might be a keypad that won’t light up, a remote that works only from ten feet away, or a gate that opens for some codes but not others. We troubleshoot low-voltage wiring, replace keypad boards, reprogram controllers, and bring the whole access system back to the way the homeowner uses it every day. In Parker, keypad or access control repair typically runs $150 – $350, with full keypad or controller replacement at $350 – $700.
Residential Keypad and Remote Repair
Keypads in North Texas sun get UV-brittle and moisture seeps into the membrane. Remotes lose programming after power surges. We re-pair, re-program, and replace worn keypads on-site, and we test every code and every remote before we leave.
Loop Detectors and Safety Inputs
When a Parker gate opens randomly or won’t auto-close, the loop detector under the drive is often sending false triggers. We trace the loop, test sensitivity, and restore the auto-close cycle so the gate doesn’t sit open for an hour after a delivery truck leaves.
Trusted Brands We Service in Parker
We work on the operator that’s already mounted on your post. FAAC 402 and 422 control boards, BFT Aries and Deimos swing arms, Linear actuators, Viking slide gate operators. We stock common control boards, capacitors, limit switches, and safety photo-eye parts for these brands, which means Parker repairs happen faster than waiting on a distributor to ship from Dallas. Manual or electric, swing or slide, we’re set up for it. We’re also set up to order rare parts for older operators so you don’t have to rip out a working FAAC because one relay failed.
Common Electric Gate Repair Problems We See in Parker Homes
- Hinge post heave and swing gate drag. Parker’s expansive clay wets in spring and dries out in late summer, so posts move. The gate starts scraping or stalling at mid-travel, and the operator struggles or trips its current limiter.
- Storm wind load on solid ornamental gates. A solid steel or iron swing leaf is a big sail in a North Texas storm. Wind bends the panel, cracks hinge welds, or pulls post anchors loose from saturated ground.
- Control board failures after electrical storms. Lightning strikes and power surges take out FAAC and LiftMaster control boards more than any mechanical failure. We replace and re-program on-site.
- Safety sensor and photo-eye faults. Sun glare, dust from the clay, and misaligned photo-eyes interrupt gate travel. A gate that reverses for no reason usually has a sensor problem, not a motor problem.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in Parker, TX
Here’s what Parker homeowners can expect on a repair invoice. Diagnostic service calls run $75 – $120. Swing gate operator repairs, including arm, limit switch, or capacitor work, run $250 – $550. Full electric gate motor replacement runs $450 – $900. Control board repair or replacement runs $300 – $700. Keypad or remote re-programming and small access control jobs run $150 – $350. New gate opener installation starts around $1,400 – $2,800 for a solid residential swing operator with two remotes, keypad, and photo-eyes. We quote the full price before any work starts, and that number is what you pay. No upcharge after the fact. Call (877) 265-5743 and we’ll give you a written number.
We Also Serve Cities Near Parker
Our crews cover Parker and the surrounding Collin County corridor: Murphy, Sachse, Saint Paul, Wylie. If you’re in any of those towns and your gate won’t budge, we’ll route the next available tech. For a closer look at what we do across the area, see Electric Gate Repair in Parker.
Serving Parker, TX — Our Local Coverage Area
We’re based in the Parker area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Parker
It’s usually the post, not the motor. Parker’s expansive clay heaves hinge posts out of plumb, so the gate leaf drops and drags against the drive or the post, and the operator stalls trying to move it. We check post plumb and gate sag first, because fixing the post usually makes the operator run clean without a motor replacement. Call (877) 265-5743 and we’ll tell you which one it actually is.
Every automatic gate operator has a manual release. On swing arms, look for a release key or lever on the operator housing; on slide gates, a pull-handle or keyed release disengages the drive sprocket. Turn the operator off at the disconnect first, release the drive, and move the gate by hand. Don’t force the gate if it’s binding, and re-engage the release after power returns. We’re happy to walk you through the exact release for your LiftMaster, FAAC, BFT, or Linear operator over the phone.
Yes. Current safety standards require photo-eyes and a reversing edge or other entrapment protection on all automatic gates, and Parker’s large-lot estates with long driveways often have multiple sets. We test and replace photo-eyes, loop detectors, and safety edges as part of every electric gate repair.
It can, especially on a long heavy leaf with no mid-rail and a tall solid infill panel. North Texas storms push enough wind load to bend thick iron, crack hinge welds, and tear a post anchor loose if the footing was shallow. We repair bent panels and hinges, and we re-set posts with deeper footings when wind or clay has loosened them.
For most slide gates, yes, if the panel is sized correctly and the site gets full sun. But Parker’s storm days and heavy clay mean you need a battery backup and a solid charging circuit, not just a panel ziptied to a post. We install and service solar operators from Ghost Controls and other brands, and we’ll tell you if your gate is too heavy or your tree line too shady for solar to be reliable. Call (877) 265-5743 for a straight answer.
Call Pinehurst Gate Repair for Electric Gate Repair in Parker
If your gate is dragging, stalled, or just refusing to open, call (877) 265-5743. We’ll diagnose the real cause, quote the repair before we touch it, and get your gate back to secure and operating the way it should. Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Parker and the surrounding Collin County area.