Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Parker, TX
Gate installation in Parker usually means a custom ornamental iron driveway gate on a large-lot property, and the job is rarely as simple as hanging steel on posts. Parker homes sit on expansive clay that moves with every wet-dry cycle, so a gate installed without accounting for soil heave will start dragging within two or three seasons. We plan every Parker install around that reality, from post depth to hinge selection, so the gate swings clean the day it goes in and stays that way. If you’re planning a new automatic gate or replacing one that’s failed beyond repair, call Pinehurst Gate Repair at (877) 265-5743 for a free estimate.
Why Parker Homes Are Different
Parker is Collin County’s quiet pocket of large-lot estates and private drives, with most homes built in the last 20 years. That housing stock matters for gate work because these are heavy ornamental iron gates, not lightweight chain-link. A 16-foot iron swing gate can weigh 800 pounds or more, and every pound of that weight sits on hinges and posts that have to stay true in soil that does not stay true. The clay under Parker expands when wet and contracts when dry, and over a few seasons that cycle quietly pushes gate posts out of plumb. When a post leans even a quarter inch, the gate leaf drops. The latch no longer lines up. The opener strains against the drag. We see this pattern constantly in Parker’s gated subdivisions and private estate drives, and it tells us a lot before we even look at the operator.
Storms and hail add their own wear. Summer heat bakes control boards inside operator housings, and a hard hailstorm can dent panels and knock sensors out of alignment. Parker homeowners also deal with HOA standards that are stricter than average. Most subdivisions require ornamental iron or steel-compatible designs, and replacement work often needs to match the existing streetscape. That’s a design consideration as much as a repair one. We account for all of it: soil movement, climate stress, and the aesthetic rules that come with living in a planned Parker community.
Styles & brands we work with
Our Main Parker Services
Two calls dominate in Parker: a gate that won’t open or close, and an automatic operator that’s stopped responding entirely. Both are covered below, with a dedicated page for each.
Gate Repair in Parker
Most repair calls in Parker start with a gate that drags, a hinge that’s sagging, or a latch that no longer catches. Clay movement is the usual root cause, but so is ordinary wear on heavy iron gates that cycle several times a day. We straighten and reinforce posts, replace worn hinges, adjust and re-weld where needed, and bring the gate back to secure, quiet operation. Whether the gate is manual or paired with an opener, the mechanical side has to be right first. Gate Repair in Parker covers the full scope, from hinge replacement to post resetting and gate realignment.
Electric Gate Repair in Parker
When the gate itself moves fine but the motor won’t run, the problem is in the operator, control board, sensors, or wiring. Parker’s clay shifts can pinch underground low-voltage lines, and summer heat can cook a board inside its housing. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule operators, so we’re not guessing at proprietary wiring diagrams. Electric Gate Repair in Parker details how we diagnose and fix automated systems from the board out.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Parker
New gate installation in Parker means building for the soil first: deeper posts, proper footings, and hardware rated for the weight of ornamental iron. We handle both manual and automatic driveway gates, and we size every operator to the gate’s true weight and cycle frequency, not to a generic spec. For a deeper look at the full installation process, our Gate Installation hub covers materials, design options, and operator selection across all our markets.
Automatic Gate Installation
Signs you need it
You’re tired of getting out of the car to open and close a manual gate, or your existing operator has failed and the gate’s mechanical condition justifies replacing the whole system rather than repairing it piecemeal.
What it costs in Parker
Automatic gate installation in Parker typically runs $4,500 to $14,500 complete, depending on gate size, operator brand, and site work required for posts and conduit.
How we do it
We set and brace new posts, hang and balance the gate, mount the operator, run low-voltage power and safety edges, then program and test full open-close cycles with obstruction and auto-close settings verified on site.
Driveway Gate Installation
Signs you need it
You have a private drive with a gate that’s undersized, rusted through at the hinges, or too light for the span, and you want a proper ornamental iron gate that closes off the property cleanly.
What it costs in Parker
Driveway gate installation in Parker generally falls between $3,500 and $12,000, with custom ornamental iron and long spans pushing toward the upper end.
How we do it
We measure the drive opening and grade, order or fabricate the gate to fit, pour and set posts below the clay movement line, hang the gate, and adjust hinges and latch until it swings true and closes flush.
What Gate Installation Costs in Parker
| Item | Typical range in Parker |
|---|---|
| Automatic gate installation | $4,500 – $14,500 |
| Driveway gate installation | $3,500 – $12,000 |
| Gate installation services (site prep, posts, hardware) | $2,500 – $6,500 |
Soil work is the biggest variable in Parker. If posts have shifted over time and the gate has been dragging, we may need to pull and reset footings, which adds labor and concrete. Custom ornamental iron, dual operators, and long spans all push the price up. Every quote is written and agreed before we start, so the number we give you is the number on the invoice.
How much does gate installation cost in Parker?
Gate installation in Parker typically runs $3,500 to $14,500 depending on size, automation, and site work. The broken-out table above shows where the money goes. Call (877) 265-5743 for an exact quote on your gate, with the price locked before work begins.
Can you install a gate in a Parker HOA community?
Yes. We work with Parker HOAs regularly and understand that most require ornamental iron or steel-compatible designs and specific setback rules. We can help you spec a gate that passes architectural review the first time. Call (877) 265-5743 to discuss your community’s requirements.
Brands We Service in Parker
We maintain service experience on FAAC, BFT, Linear, and Viking operators, along with the rest of our nine-brand line. That means when a Parker customer calls with an operator fault, we’re working from brand-specific diagnostic knowledge instead of generic troubleshooting. See our brands for the full list and what we stock locally.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Parker, TX
| Service | Typical range in Parker |
|---|---|
| Automatic gate installation | $4,500 – $14,500 |
| Driveway gate installation | $3,500 – $12,000 |
| Gate installation services (site prep, posts, hardware) | $2,500 – $6,500 |
| Gate post resetting / reinforcement | $400 – $1,400 |
| Hinge replacement (heavy iron swing gate) | $250 – $750 |
| Latch and lock replacement | $180 – $450 |
| Electric gate board replacement | $400 – $1,100 |
| Operator motor replacement | $550 – $1,600 |
Parker pricing runs higher than average because the gates are heavier and the soil work is real. HOA-compliant ornamental iron costs more per foot than standard steel, and post work in expansive clay takes more concrete and deeper footings. You get a written price before any work starts, so the total never surprises you.
Neighborhoods We Serve in Parker
Parker’s gate work is concentrated in the large-lot subdivisions and private-drive enclaves across the 75094 ZIP. We’re moving through Parker weekly, and most service calls are booked within a few days, with emergency repair slotted sooner when a gate is stuck open or pinned shut.
- Parkview Estates
- Whispering Hills
- Country Club Park
- Parker Ranch Estates
- Hillcrest Estates
Service Area – Cities Near Parker
From our base in Rowlett, we also serve the communities around Parker, including Murphy, TX, Sachse, TX, Saint Paul, TX, and Wylie, TX. Same soil conditions, same storm exposure, and the same mix of ornamental iron and automatic operators, so the diagnosis process carries right across the county line.
Serving Parker, TX — Our Local Coverage Area
We’re based in the Parker area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Parker
Most Parker emergency calls, a gate stuck open or an operator that won’t respond, can be scheduled within a day or two, and we prioritize security situations where the property can’t be secured. Call (877) 265-5743 and tell us what the gate is doing; we’ll slot you as early as the schedule allows.
We do. Most Parker HOAs require architectural review for new gates, and several have material and height standards we know well. We’ll work with your community’s guidelines from the first measurement, and we can provide whatever documentation your HOA requests for the submittal.
We’ll tell you during the repair diagnosis. If the cost to repair approaches the cost of new, we’ll quote both and let you decide with real numbers in front of you. Since we handle both repair and installation, you don’t have to start over with a different company. Call (877) 265-5743 for a free estimate either way.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Parker Customers Say
"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Sofia Flores"Gate stopped halfway and sat there for two days blocking the driveway. He found a dead capacitor in the operator, had one with him, and we were moving cars again in under an hour."
— Heather Rhodes"Solar panel on our remote gate wasn't keeping the battery up through the winter. He repositioned it, replaced the battery, and explained the math on why the old placement was never going to work."
— Diego Reyes