Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Electric Gate Repair for Rowlett Homeowners
When an electric gate stops opening, starts grinding, or refuses to close, security and daily routine both take a hit. Our Electric Gate Repair in Rowlett covers the mechanical and low-voltage electrical work needed to get a swing or slide gate operating the way it should, from hinge and roller repair to control board and motor replacement. Pinehurst Gate Repair handles this work every day, on equipment from Linear and Viking to DoorKing and Ghost Controls. We’re gate specialists, not generalists, and our experience with nine major operator brands means faster diagnosis and a fix that holds. If your gate is down right now, call (877) 265-5743 and we’ll walk through what you’re seeing before dispatch.
Gate Opener Repair
Gate opener repair covers the operator unit itself, whether it’s mounted on a post for a swing gate or alongside a track for a slide gate. You need it when the opener runs but the gate doesn’t move, the motor hums without engaging, or the unit cycles on its own. Pinehurst Gate Repair diagnoses and repairs opener problems at the board, motor, gear, and limit-switch level rather than defaulting to a replacement quote. Our pricing depends on what we find: a simple limit-switch adjustment or gear replacement runs less, while a failed control board or motor replacement costs more. Here’s what we see most often in Rowlett.
Opener Runs, Gate Doesn’t Move
This usually points to a stripped plastic drive gear, a sheared pin, or a disengaged manual release. We open the unit, confirm which component failed, and replace only what’s broken. On LiftMaster and Linear residential operators, this is one of the most common repairs we do.
Limit and Travel Problems
When a gate stops six inches short or slams at the end of travel, the limit settings or sensors have drifted. We reset travel, verify obstruction detection, and run a full cycle test. It’s a smaller job, but it can prevent real damage to the gate frame over time.
Styles & brands we work with
Automatic Gate Repair
Automatic gate repair addresses the full system, not just the motor: gate, hardware, operator, safety devices, and the low-voltage wiring tying it together. You need it when the gate opens but won’t close, closes and immediately reverses, or fails intermittently without a clear cause. Our technicians work through the entire system rather than replacing parts on a hunch, which is how automatic gate problems get fixed instead of postponed. In Rowlett, soil movement from clay-heavy ground shifts gate posts and hinge alignment over time, so a repair that ignores the foundation won’t last. Two issues dominate.
Intermittent Failures and Ghost Operation
A gate that works some days and not others often has a failing capacitor, a compromised wire splice, or moisture in a connection. We trace the low-voltage path, test voltage drop, and repair the actual fault. Ghost operation is frequently a failing receiver or an overly sensitive loop detector.
Safety Device Faults
Photo eyes, edge sensors, and loop detectors are what keep an automatic gate from closing on a car or person. When one faults, the board defaults to a refuse-to-close state, which frustrates homeowners but is the system doing its job. We test each safety input and replace the faulty device, then prove the system with a full obstruction test.
Electric Gate Motor
The electric gate motor is the powerplant inside the operator: a low-voltage DC or AC motor that drives the gate through reduction gears. You need motor service when the gate strains, moves slower than it used to, or trips its thermal overload and stops mid-cycle. Pinehurst Gate Repair tests motors under load, checks amp draw against spec, and replaces motors when they’re worn past the point of reliable operation, not before. A motor replacement in Rowlett typically runs toward the higher end of the repair range because of the part itself, but we’ll always give the number before any work starts. These two failures tell the story.
Thermal Overload Tripping
When a motor repeatedly shuts down and restarts after cooling, something is making it work harder than spec. Common culprits: worn hinge bushings, a dragging wheel, or a failing start capacitor. Treating the motor without fixing the resistance just burns out the next motor too.
Slow or Noisy Operation
A gate that groans or creeps suggests bearing wear, low voltage at the motor terminals, or a failing gear train. We measure voltage and current at the motor, then work outward to the mechanical components. It’s diagnostic work first, parts second.
Gate Access Control
Gate access control is the system that decides who gets in: keypads, intercoms, telephone entry, card readers, and the receiver that talks to your remotes. You need access control work when a keypad stops accepting codes, a remote only works from ten feet away, or an intercom no longer picks up. Pinehurst Gate Repair services the control side as thoroughly as the mechanical side, because a gate that works fine but won’t let the right people in is still broken. Access control repairs range from modest receiver swaps to full telephone-entry reconfiguration. We handle both.
Remote and Receiver Failures
Most remote problems are receiver problems, and many receiver problems are antenna or programming problems, not failed boards. We test radio range, verify programming, and check for interference sources before replacing hardware. Small remotes can also fail quietly, especially after drops or battery corrosion leaks.
Keypad and Entry System Repair
Rowlett weather is hard on outdoor keypads and intercom stations: heat, humidity, and occasional freeze cycles degrade key membranes and corrode terminals. We replace membrane assemblies, repair or replace corroded boards, and reprogram codes on site. New codes work before the truck leaves.
Commercial Gate Operator
A commercial gate operator is the heavy-duty unit on apartment complexes, business parks, and controlled-access facilities: larger motors, longer duty cycles, and integrated access systems like telephone entry or card readers. You need commercial service when the operator fails under daily use, the gate loses position data, or an access component stops talking to the operator board. Pinehurst Gate Repair has worked on Viking, DoorKing, and Linear commercial units across residential and light commercial properties. Commercial repairs in Rowlett run higher than residential because the equipment is heavier and the diagnostics run deeper. We address two recurring patterns.
High-Cycle Component Wear
A gate cycling hundreds of times a day wears gears, sprockets, belts, and chain tensioners at an accelerated rate. We inspect entire drive trains, not just the failed part, and report what’s wearing so you can plan rather than react. Property managers routinely tell us this proactive report saves them downtime later.
Integration Failures with Access Control
When the operator works but the access system won’t trigger it, the problem is often a relay, a wiring fault, or a programming mismatch between the entry system and the board. We test both sides of the integration point, which is what most fence companies can’t do. Both systems have to be right, not just the gate.
Brands We Service
We work on the brand you already have. Every manufacturer designs its control board differently, and guessing at proprietary logic means extra trips and wrong parts. Our brand-specific diagnostic experience is why a Pinehurst Gate Repair visit tends to end in a working gate, not a second appointment. We regularly diagnose and repair Linear operators, including the popular residential swing and slide units, and our team is equally comfortable inside Viking commercial operators and Electric Gate Repair – Saint Paul style DoorKing entry systems. Ghost Controls residential openers are another common sight on Rowlett properties, especially on newer installs and DIY conversions.
Whatever unit is mounted at the post or in the operator box, the diagnostic approach stays the same: test inputs, test outputs, verify the mechanical path, and only then replace what failed. Whether you have Linear, Viking, DoorKing, Ghost Controls, or any other make, we can help. If you’re not sure what brand you have, the model and serial plate on the operator will tell us, or we’ll identify it on arrival.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Gate stops mid-cycle and won’t reset. A gate that parks halfway open leaves your property exposed. The cause is often a thermal overload, photo eye fault, or lost limit position, and cycling power again without fixing the cause can burn a board.
- Motor hums but nothing moves. That hum is the motor getting voltage and not turning, which builds heat fast. A stripped gear or seized drive is likely. Running it repeatedly will take the repair from a gear replacement to a motor replacement.
- Gate reverses immediately after starting to close. Safety inputs are sensing something, even if nothing is there. A failed photo eye, nicked wire, or bad loop detector is doing exactly what it was designed to do. The fix is replacing the faulty part, not bypassing it.
- You hear grinding, squealing, or metal-on-metal. Noise means wear in hinges, rollers, track, or gear train. Hardware failures put load on the operator, which then fails too. The longer it runs noisy, the more of both sides you’ll be replacing.
- Keypad or remote stops working completely. If neither the keypad nor any remote works, the receiver or its power supply is suspect. If only part of the entry system fails, the problem is likely localized to that component. Either way, testing beats guessing.
Our Process, Step by Step
- 1
Tell us what you’re seeing. When you call (877) 265-5743, describe the symptom exactly: does it open but not close, hum, reverse, or not respond at all? That 60-second conversation lets our tech arrive with the likely parts and test equipment already in mind.
- 2
We test before we touch. On site, we start with the obvious and work inward: manual release, voltage at the board, photo eye state, limit positions. We use a multimeter and load tester to verify components under real operating conditions, not just visually.
- 3
You get a straight number before work starts. Once we know what failed and what it will take to fix, we give you the price. No work begins without your approval, and the quote you approve is the price on the invoice, not an estimate that balloons.
- 4
We repair the fault, then prove the system. We replace the failed part, reassemble, and run full cycles with obstruction tests, reversal checks, and limit verification. The gate doesn’t get called fixed until it performs under load repeatedly and consistently.
- 5
We walk you through what happened and what’s next. Before we leave, we’ll show you what failed, why it happened, and what to watch for. You’ll know whether the fix is isolated or whether other wear is coming. No mystery, no sales pitch, just an honest assessment.
How Much Does Electric Gate Repair Cost in Rowlett?
Electric gate repair in Rowlett typically runs $200 to $800 for most residential jobs, depending on what actually failed. A limit-switch adjustment, hinge replacement, or remote reprogramming sits at the lower end. Photo eye replacement, receiver swap, or drive gear work lands mid-range. Control board or motor replacement moves toward the upper end, and commercial operator work often exceeds that range because the equipment is heavier and the systems are more complex. These are honest ranges, not promises: the number we give you is based on the unit on your gate, diagnosed on site.
What moves the price: brand and age of the operator (parts availability for older units), whether the fault is electrical or mechanical, whether access control components are involved, and how much diagnostic time the fault requires. The best way to avoid overpaying is to work with a gate specialist who recognizes your unit and tests before quoting, not a generalist who quotes high to cover what they might find. Our estimate process is free, and the price we quote before work starts is the price you pay. If the repair doesn’t make sense against the value of the gate, we’ll tell you that too and show you replacement options, no pressure either way.
Our Service Area Near Rowlett
We serve Rowlett and the surrounding communities, including Garland, Sachse, Rockwall, Heath, Sunnyvale, Wylie, Murphy, Travis Ranch, Saint Paul, Mesquite, and Richardson. Most Rowlett calls are close enough that we can get a technician to your property the same day the problem is reported. If you’re in a neighboring city, see our Electric Gate Repair in Garland and Electric Gate Repair in Sachse pages for local details, or call us directly and we’ll confirm timing. For broader services, visit our home page to see the full scope of what we handle.
Serving Rowlett, TX — Our Local Coverage Area
We’re based in the Rowlett area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Electric Gate Repair in Rowlett
Electric gate repair is the diagnosis and correction of failures in automated gate systems, including the operator, motor, control board, safety devices, access control equipment, and the gate hardware itself. In Rowlett, this work covers everything from a swing gate that won’t open to a slide gate that reverses or a keypad that stopped responding. A gate specialist tests the electrical and mechanical sides of the system together, because they fail together.
Most residential repairs are completed in one visit, typically one to three hours on site. Simple fixes like limit adjustments or remote reprogramming take less than an hour, while control board or motor replacement can stretch longer. Commercial operator work may require additional time for integration testing with access systems.
Residential electric gate repair in Rowlett typically runs $200 to $800 depending on the failed component. Smaller repairs like photo eye replacement or hinge work sit low in that range, while motor or board replacement sits high. Commercial work often exceeds that range. Every job gets a confirmed price before work starts, and our estimates are free.
Yes, DoorKing is one of the nine major operator brands we service regularly, from residential swing units to commercial slide operators and entry systems. Our experience with DoorKing boards and access integration means we diagnose their proprietary systems faster than a generalist would. The same applies to Linear, Viking, Ghost Controls, and the rest of our documented brand list.
When a gate fails open or stuck closed, we treat it as a priority call and work to get a technician to your Rowlett property the same day, often within hours. Call (877) 265-5743 and describe what you’re seeing, and we’ll give you a straight answer on timing. A gate that won’t close is a security issue, not a scheduling issue.
We stand behind the parts and workmanship on every repair, and if a repaired component fails within the warranty period, we come back and make it right. New parts carry the manufacturer’s warranty, and our labor is covered as well. The specific terms depend on the part and the repair, and we’ll spell them out plainly before any work begins.
Clear access to the gate and operator is the biggest help: move vehicles away from the gate path and trim any overgrowth blocking the operator box or hinges. If you have remotes or keypad codes, have them available so we can test the full system. It’s also useful if the person who first noticed the problem is home to describe exactly what happened and when.
Schedule Your Electric Gate Repair Service in Rowlett Today
If your gate is down, noisy, or unreliable, call Pinehurst Gate Repair at (877) 265-5743. We’ll ask a few questions about what you’re seeing, get a technician scheduled for your Rowlett property, and give you a no-obligation estimate before any work begins. Manual or electric, swing or slide, we work on the brand you already have. Back to secure, operating the way it should.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, bringing straight answers and gate-specific repair to Rowlett and the surrounding communities.