Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Garland
A driveway gate that won’t open or a rolling gate stuck halfway leaves your Garland property exposed, and nobody wants to wait days for a fix. Pinehurst Gate Repair handles manual and electric gate systems across Garland’s 75043, 75044, 75045, and 75046 ZIPs, with most repair calls diagnosed on the first visit and many completed the same day. We work on the brand you already have, from a builder-grade LiftMaster operator in a newer subdivision to a 30-year-old chain-link driveway gate near Broadway. Call (877) 265-5743 for a free estimate and we’ll get your gate back to secure.
Why Pinehurst Gate Repair Is Garland’s Preferred Gate Repair Company
Garland gate problems tend to repeat in patterns, and a team that only does gates learns those patterns fast. We see the same blackland-clay post heave in 75040, the same builder-grade operator failures in 75043, and the same rusted hinge flanges in 75044 every week. That local repetition means our techs roll to a Garland job already knowing what to look for, which shortens the diagnostic time and gets your family back behind a working gate sooner.
Ronnie Beshears, owner at Pinehurst Gate Repair, runs a team of gate specialists, not generalists. We don’t split our time across garage doors, fences, sprinklers, and a dozen other trades. Gates are the whole job. Garland homeowners and property managers along the I-635 and US-78 corridors call us because we’re fluent in both low-voltage electric systems and old-school mechanical hardware. Manual or electric, swing or slide, we’ve likely fixed the exact failure you’re dealing with this month.
Having our home base in Rowlett puts a Garland call under half an hour out in normal traffic, and we keep our van stock loaded with the boards, arms, hinges, and photocells that Garland’s housing stock actually uses. If a Linear or Viking board is dead on a gate off Naaman School Road, we’re not waiting on a part order when we show up. We carry it.
Styles & brands we work with
Driveway Gate Repair in Garland
Driveway gate repair in Garland usually means one of three jobs: a gate that drags or won’t latch because the post has shifted, an operator that cycles but won’t move the panel, or a hinge that’s sagged until the gate meets the latch post on the wrong plane. On blackland clay it’s often the post, not the panel, that’s moved. A typical driveway gate repair in Garland runs $180 to $420 when it’s hinge replacement or post re-setting on a manual swing gate. Add operator diagnostics or a board swap and you’re usually at $320 to $680. We quote the full number before any work starts, and you approve it in writing before we touch a tool.
Post Heave on Slab-Edge Setups
Garland’s blackland-clay lots sit right behind slab-on-grade driveways, so a gate’s hinge post is almost always anchored in soil at the concrete edge. That’s the single spot that heaves most as the wet-spring/dry-summer cycle pulls moisture out. We re-set posts in concrete rather than packing dirt back in, and we re-hang the hinges so the gate swings true again. If your gate worked all winter and drags by August, the post moved. The gate probably didn’t.
Operator Arm and Rack Failures
Builder-grade operators on newer Garland subdivision gates often get spec’d for a panel lighter than what the homeowner actually hung. The arm burns out or the rack and pinion strips early. We replace the arm, set the travel limits correctly, and check whether the operator is sized for the panel it’s actually moving. Sometimes the fix is a repair; sometimes it’s an honest conversation about upsizing so you’re not back in the same spot next spring.
Gate Welding in Garland
Gate welding in Garland covers the metal repairs that hardware alone can’t fix: a wrought-iron-look panel with a cracked frame rail, a hinge flange torn off a tube-steel gate, or a chain-link frame rusted through at the corner. Welding runs more than a bolt-on hinge job because it’s time on site plus cleanup and repaint, but it often saves a gate that would otherwise get scrapped. A typical on-site gate welding repair in Garland runs $150 to $450 depending on how much material needs to be cut out and rebuilt. We quote it line by line before any sparks fly.
Cracked Frames and Torn Hinges
Texas sun and decades of use eventually crack the weld at the gate’s corner joints, and once one joint lets go the whole frame flexes. We cut back to solid metal, weld the joint, and reinforce it with a gusset plate where the panel sees the most stress. You get a gate that’s straight again instead of a gate that works but looks tired.
Rust Repair in Garland’s Older Stock
Plenty of Garland’s 1960s and 1970s homes still have original chain-link or metal tube gates, and North Texas humidity plus our wet springs have taken a toll. We cut out rusted sections, weld in new material, and grind the repair smooth so it takes paint cleanly. It’s cheaper than a new gate and keeps the original look of the property.
Trusted Brands We Service in Garland
We work on the brand you already have, not the brand we’d rather sell. Our Garland calls cover FAAC hydraulic swing operators on estate-style lots, BFT boards on multi-tenant gates along the I-635 industrial edge, and Ghost Controls in Garland on residential properties, plus Linear operators on subdivision entries. We carry common control boards, remotes, photocells, and loop-detector parts in the van so a Garland repair doesn’t stall while we wait on ground shipping. If your operator is a builder-grade LiftMaster, a Viking slide motor, or a Mighty Mule you bought at a big-box store, we’ve opened it up and fixed it before. Gate specialists, not generalists, means we’re already fluent in the nine major brands you’re most likely to have.
Common Gate Repair Problems We See in Garland Homes
- Builder-grade operators on under-conduit installs. In the 75043 and 75044 growth corridor, we regularly find operators that were spec’d cheap and wired even cheaper. The low-voltage wire is often surface-stapled along the fence instead of run through dedicated conduit, and the first real storm or weed-eater pass kills the signal.
- Hinge-post heave at the driveway slab edge. Garland’s clay shrinks in summer and swells in spring, and the post right at the concrete edge moves first. The panel looks fine but the gate drags by late summer because the post, not the gate, has shifted.
- Manual gates later automated without a power run. A gate installed manual at the build and automated years later usually has no in-ground run to the operator. The fix is a trench and a proper conduit run, not a quick board swap.
- Photoeye and safety-edge faults from sun and soil movement. A gate that reverses mid-cycle is often a misaligned photocell or a safety edge that’s reading a sag in the panel. On Garland’s shifting clay, these need re-alignment more often than replacement.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Garland, TX
Here’s what Garland homeowners actually pay, based on the jobs we run most weeks. Hinge replacement on a standard driveway swing gate runs $180 to $340. Post re-setting with concrete runs $250 to $450 per post. Operator diagnostics and a board swap run $320 to $680. On-site welding repairs run $150 to $450. A full operator replacement, including labor and the unit, starts around $850 and climbs depending on the brand and panel weight. The two things that move the price most are whether the post has to be dug out and re-set, and whether we’re repairing an existing power run or trenching a new one. You get a written quote before any work starts, every time. Call (877) 265-5743 for a free estimate.
In the 75043 growth corridor we were called out to a newer subdivision build where the builder had dropped a builder-grade LiftMaster operator onto a manual swing gate and never ran dedicated conduit. The low-voltage wire was surface-stapled along the fence and the post had heaved clear of the driveway slab edge. We re-set the hinge post, re-hung the hinges for sag correction, trenched a proper conduit run to the operator, and aligned the safety photocell so the UL 325 entrapment protection actually tripped again. Same trip also caught a failed loop detector on the exit side that had been masking a misaligned latch. That’s the kind of multi-point failure we see once or twice a month in Garland’s newer subdivisions, and it’s exactly why our Gate Repair team treats every call as a system, not a single symptom.
We Also Serve Cities Near Garland
Pinehurst Gate Repair covers Gate Repair in Garland and the surrounding cities, including Sachse, Rowlett, Richardson, and Murphy. If your property is right on a city line or you manage gates in more than one city, we’re already set up for that. One call schedules all of it.
Serving Garland, TX — Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Garland
The post moved. Garland’s blackland clay expands in wet springs and contracts hard through the dry summer, and a hinge post set in soil at the driveway slab edge is the first thing to heave. The panel’s fine; the post is tilted. We re-set the post in concrete, re-hang the hinges for sag correction, and the gate swings true again.
It depends on what failed and whether the operator is sized for the panel it’s actually moving. If a board died on a LiftMaster or Linear unit that’s properly sized, a repair makes sense. If the arm’s stripping or the motor’s burned out because the operator was undersized for a heavier panel, we’ll tell you straight: repair will just fail again. We quote both options and let you decide.
Yes, but the first step is a trench, not a motor. A proper in-ground conduit run from the panel to the gate post is required, and surface-stapled low-voltage wire won’t survive Garland’s weather or a weed-eater pass. We handle the full low-voltage run, then mount the operator and set the limits and safety edges.
Both. We work on residential swing gates throughout central Garland’s 75040, 75041, and 75042 corridors, and rolling slide gates on the commercial and multi-tenant fence lines along US-78, LBJ, and I-635. Same team, same van stock, same day usually.
Generally a wiring problem. In Garland’s shifting soil, low-voltage runs get stretched, pinched, or severed where the ground moves near the post. We test the keypad or loop detector first, then trace the wire. Often the component’s fine and the run is bad. Call (877) 265-5743 for an exact diagnosis. Estimates are free.
Contact Pinehurst Gate Repair in Garland
If your gate is stuck, sagging, sparking, or just stopped working the way it should, call (877) 265-5743. We’ll give you a straight answer and a written quote before any work begins. Garland properties get fast, full-service gate repair from a team that works exclusively on gates. Back to secure, operating the way it should.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Garland since day one. Gate specialists, not generalists.