Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Heath
If your driveway gate in Heath won’t open, sags at the hinge post, or makes a grinding sound every time it cycles, we can get it working again. Pinehurst Gate Repair specializes in gate systems exclusively, and we work throughout the 75032 zip code, from the lakefront properties off Ridge Road to the acreage lots east of Smirl Drive. Most Heath gate repairs take one visit to diagnose and one follow-up to complete, and we quote the full price before any work begins. Call (877) 265-5743 and tell us what your gate is doing, or not doing. We’ll walk you through the likely cause over the phone before we ever dispatch a truck.
Why Pinehurst Gate Repair Is Heath’s Preferred Gate Repair Company
Heath is a different animal than most Dallas suburbs. The lots are bigger, the gates are heavier, and the hardware takes a beating from Lake Ray Hubbard humidity. Our technicians know the difference between a sensor that needs realignment and a hinge that has seized from corrosion, because we see both constantly on Heath properties. When a gate on a one-acre lot off Laurence Drive stops responding, the problem is usually mechanical stress, not a dead remote battery.
Ronnie Beshears built Pinehurst Gate Repair around a simple idea: gate specialists, not generalists. We don’t install garage doors, we don’t patch fences, and we don’t split our crews across a dozen unrelated trades. Gate repair, electric gate repair, and gate installation are what we do. That focus means our diagnostic time is shorter and our parts van carries what Heath homes actually need. Manual or electric, swing or slide, we work on the brand you already have rather than pushing you toward a replacement you don’t need yet.
Styles & brands we work with
Gate Welding in Heath
Gate welding in Heath usually starts with a call about a gate that’s dragging on the driveway or a hinge that has torn loose from the post. The oversized ornamental gates common on Heath acreage are heavy, and when a weld fails under that load, the whole panel shifts and stresses every other component downstream.
Wrought Iron and Ornamental Steel Repairs
Most Heath welding jobs we handle involve wrought iron or ornamental steel driveway gates. A cracked weld at the hinge mount, a broken picket, a sagging frame joint. We grind back the failed weld, re-weld with proper penetration, and repaint the repair area so it doesn’t flash rust within a season. A typical hinge mount re-weld on an ornamental gate in Heath runs $180 to $340, depending on access and how much disassembly the repair requires.
Aluminum Gate Frame Reinforcement
Aluminum gates are lighter but they crack differently than steel. When an aluminum frame cracks at a stress point, welding alone won’t hold; we add an internal gusset or sleeve before closing the weld. Homeowners off Smirl Drive and along the lakefront have this done when a gate starts wobbling at the mid-rail. Expect $220 to $420 for a reinforced aluminum frame repair, including paint matching on the visible surface.
Commercial Gate Repair in Heath
Commercial gate repair in Heath tends to involve slide gates, barrier arms, and operators that cycle hundreds of times per day rather than a few dozen. HOA entrances off Ridge Road, private community gates, and small ranch properties with livestock all fall into this category. The failure mode is almost always cumulative wear: a motor that’s been running hot, a chain that’s stretched, a limit switch that’s drifted out of adjustment.
Slide Gate Track and Roller Service
When a commercial slide gate in Heath starts shuddering or jamming halfway open, the track and roller assembly is the first thing we inspect. North Texas clay soil moves with every wet-dry cycle, and that movement can leave a track slightly out of level within a couple of years. We re-level track sections, replace worn roller bearings, and set the chain tension so the operator stops working against itself. Typical track and roller service in Heath runs $280 to $520 depending on gate length and whether we need to bring in concrete repair for the track bed.
Operator Replacement and Control Board Diagnostics
A commercial operator that fails in Heath usually isn’t dead; it’s been overloaded by a mechanical problem downstream. We diagnose control board faults on FAAC, BFT, Linear, and Viking operators before we quote a replacement. If the board is burned out from a seized wheel, we fix the mechanical root cause first, then install the new board. Control board replacement on a commercial slide operator in Heath typically runs $340 to $680, and operator replacement starts around $1,200 for a mid-range slide unit. Every quote includes the full scope before we touch a wire.
Trusted Brands We Service in Heath
Pinehurst Gate Repair services equipment from nine major gate and operator brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That’s not a marketing line; it’s what’s on the shelves in our service van. Whether your FAAC board has lost power after a storm or your Viking slide operator is straining against a misaligned track off Laurence Drive, we don’t have to special-order diagnostics time or guess at proprietary motor specs. Brand-specific knowledge means faster repairs, and for Heath customers that means less time with an open, unsecured entry.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Heath Homes
- Seized hinges and corroded control boards on lakefront gates. Lake Ray Hubbard humidity accelerates rust on original steel hardware, and once a hinge seizes, the operator strains against it until the board burns out. The fix is replacing the hinge set with rust-resistant hardware, not just resetting the breaker.
- Sagging gate panels from clay-soil movement. Heath sits on expansive clay. When the soil swells after rain and shrinks during dry spells, gate posts shift, and the gate drops out of alignment. Sag correction at the hinge post, not operator adjustment, is the repair that lasts.
- Underground operator failures on heavy driveway gates. Many Heath homes use underground operators, and when water infiltrates the vault or the original steel housing corrodes, the motor locks up. We dig out the vault, assess the operator, and either rebuild or replace it with a unit rated for the gate’s actual weight.
- Long driveway power and signal issues. Gates at the end of a 200-foot drive often lose communication with the house or the keypad, especially after storms. We run low-voltage signal checks and repair or replace the wiring run so the gate arms when it actually should.
Pricing for Gate Repair in Heath, TX
Hinge post sag correction on a typical Heath ornamental gate runs $260 to $480. A seized hinge set replacement, including rust-resistant hardware and realignment, runs $320 to $550. Control board replacement on a residential swing operator runs $240 to $460, while a complete operator replacement starts around $800 and goes up based on gate weight and whether the unit is underground or surface-mounted. Weld repairs fall in the $180 to $420 range depending on the break. Every job is quoted and agreed before work starts, so the number you approve is the number you pay. Call (877) 265-5743 for a free estimate.
We Also Serve Cities Near Heath
Our Gate Repair team regularly works in Heath and the surrounding communities, including McLendon-Chisholm, Rockwall, Fate, and Royse City. If you’re in one of those areas and you’re seeing the same clay-soil and humidity problems Heath homeowners deal with, call us. We understand this stretch of Rockwall County, and our Gate Repair in Heath experience applies directly to the neighboring acreage lots and lake-adjacent properties.
Serving Heath, TX — Our Local Coverage Area
We’re based in the Heath area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Heath
In Heath, near Lake Ray Hubbard, the humidity works its way into hinge barrels and corrodes the original steel pins from the inside, so surface lubrication doesn’t reach the problem. Once the internal bearing surface is pitted, the hinge seizes again within weeks. The only lasting fix is replacing the hinge set with rust-resistant hardware. A setback hinge replacement on an ornamental Heath gate runs $320 to $550, and that price includes realigning the gate after the new hardware goes in. Call (877) 265-5743 and we’ll assess whether your hinges are salvageable or ready for replacement.
No. On Heath gates, a sag in the middle is almost always caused by hinge post movement from clay-soil expansion and contraction, not by an operator that lost its limit setting. Adjusting the operator without correcting the post lean masks the problem for a few weeks, then the gate binds again and the operator burns out trying to push against the misalignment. We correct the post alignment and reset the gate’s geometry first. Sag correction at the hinge post in Heath runs $260 to $480. Get the free estimate at (877) 265-5743 before the operator becomes the next casualty.
You can, but it depends on your tree cover and how many cycles the gate runs per day. Heath’s partially wooded lots, especially off the lake, can shade a solar panel for large parts of the day, which leaves the battery undercharged and the gate dead by mid-week. We size the panel and battery bank to your specific gate weight and cycle count before we recommend anything. For most Heath drives over 150 feet with tree cover, we recommend a wired low-voltage run instead. Call (877) 265-5743 and we’ll look at your site and give you a straight answer, not a catalog.
Every automatic gate in Heath must protect against entrapment. That means photo eyes or contact edges that stop and reverse the gate when something is in the path, and on heavier slide gates, secondary entrapment protection like a reversing edge is standard practice. When we service a gate off Ridge Road or anywhere in the 75032 zip code, we verify that every safety device is present and functional before we consider the job done. A gate that opens reliably but doesn’t stop for an obstruction is a liability, not a fix. Call (877) 265-5743 if you want a safety inspection done alongside your repair.
Yes. We service commercial slide gates and heavy ranch-style gates on Heath properties that keep livestock, and we understand what an open gate means in that context: animals get out, and that’s a different kind of emergency than a stuck driveway gate. When a slide gate with livestock on the other side fails, the operator has typically been loaded beyond its duty cycle by a mechanical problem like a worn track or stretched chain. We repair the mechanical root cause before we replace or reprogram the operator. A commercial slide gate repair in Heath runs $280 to $680 depending on the scope, and we’ll give you the full quote before work starts. Call (877) 265-5743.
On a wooded lot off Heath’s Lake Ray Hubbard shoreline, our crew repaired a seized LiftMaster swing gate operator on a custom wrought-iron gate. The original steel hinges had corroded from the humidity, causing the gate to sag and the operator to strain. We replaced the hinge set with rust-resistant hardware and performed sag correction at the hinge post, restoring smooth operation without touching the control board. That’s the fix most Heath gates actually need: hardware first, electronics second.
If you’ve got a gate in Heath that won’t open, won’t close, or won’t stay aligned, call (877) 265-5743. We’ll ask what the gate is doing, tell you what we think is wrong, and give you a free estimate to fix it. The price you approve is the price you pay, and the work gets done right the first time, by a crew that works on gates every single day.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Heath and the surrounding communities.