Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Saint Paul
Gate repair in Saint Paul usually costs $185 – $640, and most hinge resets, latch fixes, and operator diagnostics can be handled in a single visit. Pinehurst Gate Repair works on the brand you already have, whether it’s a builder-grade aluminum driveway gate on a 2005 tract home or a newer Ghost Controls operator on a vinyl privacy gate. If your gate is dragging, binding, or refusing to open in Saint Paul, call (877) 265-5743 and we’ll walk you through what’s wrong before anyone even rolls a truck.
We know Saint Paul’s streets and subdivisions well: the tight side yards off Ballard Street, the shared driveways along the newer sections near the Wylie border, and the 75098 ZIP’s mix of 1990s starter homes and 2010s builds. Local expertise matters because a gate that won’t latch on a Saint Paul lot is rarely just a hinge problem. It’s usually the ground under the post. More on that below.
Why Pinehurst Gate Repair Is Saint Paul’s Preferred Gate Repair Company
Most companies that show up for gate work in Saint Paul are fence companies or garage door shops that pick up gate jobs on the side. We’re not that. Gates are the entire job. Our techs spend every working day on swing gates, slide gates, operators, loop detectors, and the control boards that run them. That focus shows in how fast we isolate a problem. When a DoorKing board loses communication with its safety edge, we’re not guessing at pinouts. We know that board.
Saint Paul homeowners and the HOA management companies that call us keep calling back for a few reasons: we stock parts for the brands installed across this corridor rather than ordering every component and making the gate wait a week, and we don’t quote a replacement gate just because a hinge post settled. The fix is usually a post reset, and that’s the quote you get. Ronnie Beshears, who owns and runs Pinehurst Gate Repair, built the company around one idea: fix what’s fixable, replace only what’s actually failed.
Styles & brands we work with
Driveway Gate Repair in Saint Paul
Driveway Gate Repair makes up the bulk of our Saint Paul calls. On a Saint Paul lot, the driveway gate is the one piece of hardware that gets cycled twice a day, every day, in direct sun and North Texas wind. Most driveways here are narrow enough that the gate is a slide rather than a swing, which puts constant wear on the track, rack, and pinion. Add expansive clay under the track slab and you get a gate that runs fine in March and stalls halfway open by July. We see it constantly.
Typical driveway gate repair in Saint Paul runs $225 – $640 depending on what actually failed. A hinge-post reset, fresh hardware, and panel rehang usually falls in the $300 – $500 range. A new slide-gate rack or a track section runs lower. Before we touch anything, you get a written price. Not an estimate that grows after we open the panel. The number we quote is the number you pay.
Hinge Post Reset and Realignment
On Saint Paul clay, the most common driveway gate failure is a hinge post that has lifted or tilted. The panel itself is still straight. The post moved. We pull the footing, set the post back to grade with concrete below the clay’s active zone, and re-hang the gate square. That’s a repair, not a patch. It holds through summer droughts and spring rains.
Slide Gate Track and Rack Repair
For the slide gates common on Saint Paul’s narrower lots, the track takes the abuse. The gate drags, the rollers flatten, the rack teeth wear unevenly. We replace worn rack sections, dress and level the track, and set the travel limits so the gate isn’t slamming against its stop. A slide gate that rolls easily is a slide gate that stops chewing through operators.
Gate Welding in Saint Paul
Gate Welding is where a lot of Saint Paul repair jobs end up, especially after a spring hail storm or one of those gusty winter fronts that racks a builder-grade gate frame. Aluminum and ornamental-steel gates crack at the weld points, not in the middle of the tube. Weld repair that’s done right means grinding the break, prepping the joint, and re-welding with the gate hung in place so the alignment stays true. Weld-and-paint patch jobs are not how we work.
In Saint Paul, gate welding typically runs $150 – $450 per repair point depending on the material, the location on the gate, and how much finish work is needed after the weld. Aluminum costs a bit more than steel because of the prep and filler material. We weld on site. For ornamental steel, we match the finish as closely as possible. For aluminum, we dress the weld and leave it clean, not blobbed.
Steel and Aluminum Frame Repair
Builder-grade ornamental steel gates around Saint Paul often have thin-wall tube frames. The welds at the mid-rail and hinge stiles crack first. We reinforce the joint, not just the crack, so the repair doesn’t move the failure point six inches down the rail. The gate should look like a gate, not a patchwork.
Hinge Reinforcement Welding
When a hinge tears out of the gate stile, a bolt-on plate is a temporary fix. We cut out the torn steel, weld fresh material behind the stile, and re-drill the hinge face so the gate swings on solid metal. Same for aluminum. The difference is in the prep and the alloy.
Trusted Brands We Service in Saint Paul
We work on the brand you already have. Saint Paul homes run everything from original-builder Linear and Viking swing operators to newer Ghost Controls and DoorKing units added after closing. Our techs carry diagnostics and common control parts for these systems so a board-level issue doesn’t mean a two-week wait. Whether your Viking swing arm has stopped mid-cycle or your Linear receiver won’t respond to the remote, we diagnose against the actual equipment, not a generic flowchart. Gate Repair is all we do, so brand-specific training isn’t a nice-to-have here. It’s the baseline.
Common Gate Repair Problems We See in Saint Paul Homes
- Summer gate drag and latch pop-out on expansive clay. The hinge post settles as the black clay dries and shrinks, the gate drops a half-inch, and a gate that latched clean in April won’t catch in August. The fix is a post reset, not endlessly adjusting the latch.
- Racked frames from hail and north winds. Builder-grade aluminum and thin ornamental steel bend where the operator pushes, especially after a spring storm. The operator may be fine. The frame isn’t. Weld and straighten before the motor burns itself out fighting the bend.
- Slide gates stalling mid-run on short, narrow lots. Saint Paul driveways don’t have room for a big swing arc, so slide gates are everywhere. When the track fills with clay sediment or the rack wears, the gate stalls and the operator reverses. Cleaning the track helps for a week. Rebuilding it fixes it.
- Shared driveway slide gates blocking both neighbors. When a loop detector fails or the operator logic faults, a stalled slide gate across a shared Saint Paul driveway stops everyone. We work one leaf at a time and keep pedestrian access open so the repair doesn’t close the driveway down.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Saint Paul, TX
Saint Paul gate repair pricing breaks down into a few honest ranges. A basic latch adjustment, hinge lubrication, or limit reset on a residential gate runs $185 – $275. Hinge post resets with fresh hardware land between $300 and $500. Gate welding runs $150 – $450 per repair point. A full slide-gate track and rack rebuild can reach $600 – $900. Operator board replacement depends on the brand: a DoorKing board costs more than a Ghost Controls board, and we’ll tell you the number before you approve anything. Every job gets a written price up front, agreed before work starts. Call (877) 265-5743 for a free estimate on your Saint Paul gate.
We Also Serve Cities Near Saint Paul
While this page is for Gate Repair in Saint Paul, our techs cover the surrounding Collin County corridor most days of the week. If your gate is in Wylie, Sachse, Murphy, or Parker, the same brand-specific diagnostics and post-reset repair work applies, and the drive from our Rowlett shop is short enough that we treat those cities as local service territory.
Serving Saint Paul, TX — Our Local Coverage Area
We’re based in the Saint Paul area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Saint Paul
It’s almost always the ground. Saint Paul sits on North Texas black clay that shrinks hard in summer drought, pulling away from shallow builder-installed post footings and letting the hinge side settle. The gate drops, the latch misses, and the panel drags. We fix it by re-setting the post below the clay’s active zone, not by shimming the latch. Call (877) 265-5743 and we’ll tell you if your gate matches the pattern.
Yes, and we do it regularly. Saint Paul’s tighter lots off FM 1378 and Ballard Street are exactly where slide gates get installed because there’s no arc for a swing. We rebuild tracks, replace worn rack and pinion sections, dress rollers, and reprogram travel limits so the gate doesn’t stall mid-run. No need to convert to a swing gate that won’t fit.
The gate’s reversing on its own usually means the safety loop detector or the inherent obstruction sensor is triggering false positives, often from clay sediment in the track or a weak battery in the wireless edge. LiftMaster service in Saint Paul, FAAC, and BFT boards each log and react differently. We diagnose against the actual board, and we stock common replacement parts for all three. Call (877) 265-5743 and we’ll walk through the first checks with you by phone.
We weld on site, with the gate still hung. Taking a gate down and hauling it to a shop means re-hanging it blind and hoping the alignment is still square. We grind the break, prep the joint, and weld it in place where the geometry is real. Ornamental steel and aluminum both weld fine on a Saint Paul driveway.
We work one leaf at a time on double gates and keep the pedestrian side open on slide gates. For shared driveways in Saint Paul’s newer subdivisions where both neighbors depend on one gate, we schedule the work so vehicle access is down for the shortest possible window, and we stage our truck so it never blocks the right of way. Your neighbors won’t be stranded while we work.
Contact Pinehurst Gate Repair in Saint Paul
If your Saint Paul gate is dragging, racking, failing to latch, or the operator won’t respond, call (877) 265-5743 for a free estimate. We’ll diagnose what’s actually wrong over the phone when we can, give you a written price before any work starts, and send a gate specialist, not a generalist. Serving Saint Paul and the surrounding Collin County corridor. Saint Paul gate work is what we do every day.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Saint Paul, TX.