Farm & ranch
Wrought iron
Wood & steel frame
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Travis Ranch
Most gate repairs in Travis Ranch come down to one of three problems: a hinge post heaved out of plumb by blackland clay, a weld seam rusted through on a builder-grade steel frame, or an opener arm that’s worn past adjustment. We fix all three, usually in one visit. Pinehurst Gate Repair works on the brand you already have, whether the gate is manual or electric, swing or slide. If your gate is dragging, sagging, or refusing to open, call us at (877) 265-5743 and we’ll get it back to operating the way it should.
Why Pinehurst Gate Repair Is Travis Ranch’s Preferred Gate Repair Company
Travis Ranch is a master-planned community where nearly every home was built between the mid-2000s and early 2010s with the same builder-grade wood-and-steel driveway gate. We’ve worked on hundreds of those gates. That repetition gives us an advantage a generalist doesn’t have: we see the same failure points week after week, so we diagnose them faster and know exactly which repairs hold up in this soil and this climate. When a homeowner off Ridge Road or near the Travis Ranch park calls about a gate that drags on one corner, we don’t have to guess.
Our technicians are dedicated gate specialists, not a multi-trade crew squeezing gate work between fence and garage-door jobs. We’re factory-trained and hands-on experienced with FAAC, BFT, Linear, LiftMaster, Viking, and more. Manual hinge repair, electric gate troubleshooting, full electric gate repair, it’s all we do. That matters when a control board fails and the problem isn’t visual; brand-specific diagnostic knowledge means we don’t spend two hours swapping parts to find the fault. We find it, quote it, and fix it.
Styles & brands we work with
Sliding Gate Repair in Travis Ranch
Sliding Gate Repair in Travis Ranch is a different job from swing gate work, and it’s one we handle regularly for properties with wider than standard driveway openings or gates that can’t swing inward because of grade or landscape. A sliding gate rides on a track and rollers or a cantilever system, and when a roller bearing fails or the track fills with debris and clay silt, the gate binds, grinds, or stops mid-cycle. Some Travis Ranch homes with side-loading garages and rear driveway access use slide gates on the alley side. We replace rollers, straighten or re-bed track, re-shim wheel carriages, and re-set stop brackets.
Track and Roller Replacement
A sliding gate that shudders and screeches while moving usually has a seized roller, a bent axle, or a rusted track section. We remove the gate from the track, replace worn rollers with sealed-bearing units, de-scale and clean the track, and re-align the gate in its run. We quote the full job before touching a bolt.
Operator Arm and Chain Repair
Slide gates open with either a chain-drive or belt-drive operator, or a direct rack-and-pinion setup. When a chain link snaps or a rack tooth strips, the gate jerks and stops, and the motor strains against the bind. We repair or replace the drive components, check motor load, and re-set travel limits so the gate doesn’t overrun the track.
Wrought Iron Gate Repair in Travis Ranch
Wrought Iron Gate Repair in Travis Ranch usually means repairing a steel gate panel that’s rusted at the joints, sagging on one hinge post, or damaged at the bottom rail, plus restoring the gate so it closes square and latches without lifting. True wrought iron is rare in this subdivision; most Travis Ranch gates are welded steel with a wrought-iron look. The repair method is similar. We grind out rust, repair or replace bottom rails, re-weld broken pickets, and reinforce hinge plates that have torn loose from the frame.
Hinge and Post Resetting
A steel gate that sags until the latch misses the striker is almost never a panel problem alone. The hinge post has moved, or the hinge welds have cracked. We remove the gate, re-plumb the post in its concrete footing, replace hinges with heavier units when needed, re-weld and re-hang the panel, and dress the repair so it looks original.
Weld and Rust Repair
The weld seams at the corners and mid-rail are where Travis Ranch gates rust first, because water sits in the seam and the factory paint is thin there. We cut out the corroded section, weld in sound material, grind smooth, prime, and topcoat to match. The gate leaves our truck quieter, stiffer, and sealed against further rust.
Trusted Brands We Service in Travis Ranch
We work on the gate operator you already have. That includes FAAC hydraulic and electromechanical swing operators, BFT slide and swing boards, Linear residential operators common on smaller subdivision gates, and Viking units used on wider and commercial style entries. Because so many Travis Ranch gates are builder-installed, most homes share a small pool of operator models and control boards. We carry common boards, photocells, remotes, and limit switches for those brands on the truck, which means fewer second visits and a faster turnaround for Travis Ranch homeowners. If your opener isn’t one of the common models, we still diagnose and order exact parts by model number.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Travis Ranch Homes
- Blackland clay heaving hinge posts out of plumb. After wet-dry cycles, the soil under a post swells and lifts the footing, and a gate that was level in October drags on the strike side by March. We re-set the post in new concrete and re-align the gate.
- Builder-grade steel frames rusting at the weld seams. Hundreds of matching Travis Ranch gates are now 15 to 20 years old, and the factory welds are the first place rust thin out. We repair or replace the seam before the bottom rail separates.
- Sagging wood-and-steel panels pulling away from the hinge post. The wood infill swells with moisture and the added weight pulls hinge screws and lag bolts loose. We re-hang with through-bolts and reinforcement plates.
- Worn opener arms and failing solar gate opener setups. On Travis Ranch lots with longer driveway setbacks or no practical mains power at the gate position, solar operators run batteries low and the arm loses strength. We test charging, replace batteries, and re-check stroke and obstruction sensitivity.
Pricing for Gate Repair in Travis Ranch, TX
We Also Serve Cities Near Travis Ranch
Pinehurst Gate Repair works throughout the northeast Dallas suburbs, including Forney, Sunnyvale, Talty, and Seagoville. We also handle Gate Repair for customers across the wider Rowlett area. If you’re in Travis Ranch or a nearby community, Gate Repair in Travis Ranch is a single call away.
Serving Travis Ranch, TX — Our Local Coverage Area
We’re based in the Travis Ranch area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Travis Ranch
It’s almost always blackland clay heaving the hinge post upward. Travis Ranch sits on North Texas blackland clay soil, which swells when wet and shrinks when dry. The fixed side post and the gate post move at different rates, and the gate drags on the latch corner only during wet periods. The fix is re-setting the post in a properly bedded footing. Call (877) 265-5743 and we’ll confirm the cause and quote the repair.
Yes. Some Travis Ranch properties on quarter-acre lots have driveway gates set back far enough from the house that running line-voltage power to the gate position is impractical. We repair solar gate opener setups and 12-volt systems, and we can convert a manual wide gate to a solar-powered opener with a battery backup. We service FAAC, BFT, Ghost Controls, and Mighty Mule solar units. We test the panel output, battery condition, and arm force before quoting.
Only sometimes. A Travis Ranch gate that sags in the middle has either a failed mid-rail weld, a rotted wood infill panel that has lost its diagonal strength, or a hinge post that has shifted out of plumb. We measure the gate square, check post plumb and hinge wear, and identify which one is doing the work before we cut or replace anything. The panel itself is the last thing we blame.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Travis Ranch, the commonest operator boards we see are LiftMaster and Linear units installed with the original builder package. We carry parts for those in the truck.
Yes. Every automatic gate installed or repaired in Travis Ranch must meet UL 325 entrapment standards, which means safety photocells, obstruction sensing, and audible alarms on certain installations. We check entrapment protection on every electric gate repair, and we will not set a gate to operate without it. If an existing system ignores or defeats that safety requirement, we correct it. Call (877) 265-5743 to schedule a safety and operation check.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Travis Ranch and the surrounding communities.