Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Garland, TX
Gate installation in Garland usually means replacing a wood or chain-link gate that has finally given out after decades of Texas sun and shifting clay soil. We’re Pinehurst Gate Repair, and we handle both the mechanical and electrical sides of gate work: manual gates, automated operators, and full driveway gate installations across Garland’s 75043, 75044, 75045, and 75046 ZIP codes. If your gate is dragging on the concrete or the operator has stopped responding, call us at (877) 265-5743 and we’ll tell you exactly what’s wrong before any work is quoted.
Why Garland Homes Are Different
Garland’s gate problems follow a pattern we see on nearly every service call. The city’s blackland clay soil expands hard during wet springs and contracts just as aggressively through the dry North Texas summer, and that movement is brutal on gate posts. A gate that swings clean in February will often drag the driveway by August because the post footing has heaved a half-inch as the soil dried out. Most Garland gates sit anchored in soil right at the slab edge, which is exactly where the shift concentrates.
The housing stock makes it worse. Garland’s central neighborhoods, built largely between the 1950s and 1980s, are full of original wood privacy gates, chain-link driveway gates, and older wrought-iron-look steel frames that have been hanging on the same hinges for thirty or forty years. In the 75043 and 75044 corridor where lots are larger and homes are newer, we see more ornamental metal and automatic openers, but the same soil movement still wins. We routinely re-set posts and re-hang hinges instead of replacing the entire gate, because in Garland the frame is usually fine. It’s the footing that failed.
Styles & brands we work with
Our Main Garland Services
Garland homeowners reach out for two things most often: a gate that won’t close properly and an electric operator that has quit working. Here’s what each involves here.
Gate Repair in Garland
Most Garland gate repairs start with a post that has leaned, a hinge that has sagged, or a latch that no longer lines up. On older wood gates, the UV and heat have usually warped the frame enough that the latch pin sits a quarter-inch off the catch. We re-set posts in fresh concrete on the older central Garland lots, replace worn hinges, and rebuild latch alignment rather than selling you a whole new gate. If your gate is dragging or won’t stay latched, Gate Repair in Garland has the full breakdown of what we fix and how we price it.
Electric Gate Repair in Garland
Electric gate failures in Garland tend to follow the seasons. Summer heat cooks control boards and power supplies, and the same clay soil that shifts manual gates also flexes the mounting rail on slide operators until the chain or belt slips. We diagnose both the mechanical side and the low-voltage control side, so we know whether your issue is a failed FAAC board, a stripped gear, or a misaligned safety sensor. To see how we handle automated systems from LiftMaster to Viking, visit Electric Gate Repair in Garland.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Garland
Full gate installation in Garland is usually a replacement-and-refit job rather than new construction. The central neighborhoods are full of original wood and chain-link gates that have outlived their hinges, and the 75043/75044 growth corridor has larger lots with newer driveway gates that need to be sized for wider openings and heavier steel. Climate is the deciding factor on every install: if we don’t set posts below the frost line and account for clay movement, a new gate will be dragging within two years. We quote every Garland installation as a complete job with post-setting, hanging, hardware, and operator wiring where it applies. See our full Gate Installation scope for what a complete install includes.
Automatic Gate Installation
Signs you need it
You’re tired of getting out of the car to open a heavy gate, or you’re adding a perimeter gate to a new build and want operator wiring planned before the concrete is poured.
What it costs in Garland
Automatic gate installation in Garland typically runs $1,900 to $5,400 for a full system with operator, safety edges, and low-voltage wiring, depending on gate width and brand.
How we do it
We set the posts deeper than the local clay shift line, mount the operator on a reinforced pad, run the low-voltage line in conduit, and test the full open-close cycle with the safety reversing edges before we hand it back.
Driveway Gate Installation
Signs you need it
Your existing driveway gate is sagging, the post is leaning toward the concrete, or you’re adding a gate to a driveway that never had one.
What it costs in Garland
A new driveway gate in Garland typically costs $1,200 to $3,800 installed, with steel and ornamental metal frames on the upper end and treated wood or chain-link lower.
How we do it
We measure the opening, pull the old posts if the footing is cracked, pour new footings reinforced for the gate weight, hang the new frame, and align the latch and drop rod.
Electric Gate Installation
Signs you need it
You already have a manual swing or slide gate and want to automate it, or the old operator on your current gate has failed beyond repair and you need a fresh system.
What it costs in Garland
Electric gate automation in Garland runs $1,900 to $5,400 for a complete operator and control package, with commercial slide operators running toward the higher end.
How we do it
We mount the operator on a concrete pad or steel post, run low-voltage power in conduit from the nearest exterior outlet, install the control board and safety sensors, and program the travel limits to match the gate’s exact swing.
Sliding Gate Installation
Signs you need it
Your lot opens onto a busy street or you don’t have room for a swing arc, so a rolling gate makes more sense for the driveway.
What it costs in Garland
Sliding gate installation in Garland typically costs $1,900 to $4,800, with cantilever steel frames priced by the opening width and track systems adjusted for the driveway slope.
How we do it
We set the track or cantilever rollers on a level rail, hang the gate, install the motor and rack gear, and fine-tune the open and close limits so the gate stops soft on both ends.
What Gate Installation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Automatic gate installation (full system) | $1,900 – $5,400 |
| Driveway gate installation (manual) | $1,200 – $3,800 |
| Sliding gate installation | $1,900 – $4,800 |
How long does a gate installation take in Garland?
Most residential gate installations take one full day, including post concrete work. Adding an electric operator or building on a steeper lot can stretch the job to two days. We’ll quote your timeframe when we measure and confirm the scope.
Do I need a permit for a gate in Garland?
For most standard residential replacements on the same post line, you won’t. If the gate is taller than local code allows or we’re running new electrical to an operator, the city may require a permit. We’ll check Garland’s current requirements before we start.
Brands We Service in Garland
We work on the brand you already have. Pinehurst Gate Repair carries diagnostic and replacement parts for FAAC, BFT, Linear, and Viking operators, plus the mechanical hardware that works across any manufacturer. If your existing opener isn’t one we stock, we can source the board or motor quickly. See our brands for the full list of what we service.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Garland, TX
| Service | Typical range in Garland |
|---|---|
| Gate repair (manual, residential) | $80 – $320 |
| Gate post reset and re-hang | $200 – $500 |
| Electric gate operator repair | $185 – $400 |
| Gate opener circuit board replacement | $200 – $500 |
| Gate opener full replacement | $600 – $1,600 |
| Gate wheel and roller replacement | $75 – $200 |
| Automatic gate installation (full system) | $1,900 – $5,400 |
| Driveway gate installation (manual) | $1,200 – $3,800 |
| Sliding gate installation | $1,900 – $4,800 |
In Garland, the two biggest price movers are soil condition and gate weight. A post that has to be dug out of dry blackland clay and re-poured with a deeper footing costs more than a simple hinge swap, and a heavy ornamental steel gate wears out rollers and hinges faster than a lighter chain-link frame. Whatever the job, your price is quoted and agreed before any work starts, so there are no surprises on the invoice.
Neighborhoods We Serve in Garland
We cover the full Garland footprint, from the older 1950s-80s neighborhoods in the central ZIPs to the newer subdivisions and larger lots in the 75043 and 75044 corridor. These are the areas we work in most often:
- Club Hill
- Crystal Lake
- Oakridge
- Travis College Hill
- Valley Creek
Most Garland calls get a same-week appointment, and repair emergencies can usually be scheduled within 24 to 48 hours depending on parts.
Service Area – Cities Near Garland
Pinehurst Gate Repair is based nearby in Rowlett and serves Garland plus the surrounding corridor. We work regularly in Rowlett, TX, Sachse, TX, Richardson, TX, and Murphy, TX. If your gate is down and you’re just outside the Garland line, call us and we’ll tell you if we can get to you this week.
Serving Garland, TX — Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Garland
We schedule most Garland repair visits within 24 to 48 hours, and if a gate is stuck open or won’t secure we do our best to fit you in same-week. Call (877) 265-5743 and tell us what the gate is doing and we’ll give you a straight answer on timing.
If you’re in a Garland HOA, the short answer is usually yes for style or height changes. A like-for-like replacement often doesn’t trigger review, but we recommend checking your covenants first. We can provide specs and drawings if your HOA needs details before the install.
Yes. We repair and install manual swing gates for Garland homes and rolling or slide gates for commercial and multi-tenant fence lines along the US-78/LBJ and I-635 corridor. One call covers both types, and we’ll tell you whether the gate can be salvaged or needs replacement.
Call Pinehurst Gate Repair at (877) 265-5743 for a free estimate on any gate job in Garland. We’ll come out, find the actual problem, and quote your price before any work begins.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Garland Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
— Arjun Reddy"Hinge post had rotted at the base and the whole swing gate was sagging into the concrete. He rebuilt the post rather than talking us into a whole new gate, which two other companies had pushed for."
— Renee Hayes"Reprogrammed every clicker in the HOA and set up the keypad codes. Patient with a very long list of residents."
— Rami Hassan