Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Rowlett Homeowners
A gate that won’t open, won’t close, or groans halfway through its cycle isn’t something to put off. It’s a security gap, a daily frustration, and a problem that only gets more expensive the longer it sits. For everything that can go wrong and how we fix it, read The Complete Gate Repair Guide for Rowlett Homeowners. Pinehurst Gate Repair fixes gates in Rowlett, TX, and we’re gate specialists, not generalists. Our team works on manual and electric systems across nine major brands, from residential swing gates to commercial slide operators. If your gate is stuck, sagging, or dead at the panel, call (877) 265-5743 for a free estimate. Most Rowlett repair calls we handle are diagnosed and fixed in a single visit.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Rowlett and surrounding North Texas communities.
Driveway Gate Repair
Driveway gate repair in Rowlett covers everything from a gate that has dropped on its hinges to a keypad that stopped talking to the control board. Driveway gates take a beating in North Texas: clay soil shifts with wet-dry cycles, heat expands metal, and daily opening cycles wear out rollers, hinges, and operator arms. When your driveway gate fails, it’s either a mechanical problem, an electrical problem, or both. Our technicians diagnose the full system, not just the symptom, so the fix is right the first time.
Hinge and Post Work
Rowlett’s expansive clay soil is hard on gate posts. When a post shifts even an inch, the gate binds, the operator strains, and the whole system suffers. We reset and reinforce posts, replace or rebuild heavy-duty hinges, and true the gate so it swings or slides clean.
Operator Diagnosis and Repair
If your opener hums but the gate doesn’t move, or it stops mid-cycle with a blinking error code, the problem is usually the control board, a limit switch, or a failing motor capacitor. We carry diagnostic tools and brand-specific parts for the common residential operators so we’re not guessing at proprietary boards.
Styles & brands we work with
Gate Welding
Gate welding is the fix when a structural member cracks, a hinge tears away from the post, or a section of metal has fatigued to the point it can no longer support the gate’s weight. Not every gate repair shop welds. Not every welder understands how a gate has to flex under load. Our team does both: we weld to structural standard and keep the gate operating the way it should afterward. A clean weld restores strength without warping the gate frame or throwing off the alignment.
Cracked Frames and Hinge Points
On iron and tube-steel gates, the most common fatigue points are at the hinge welds and the lower corners. We grind out the failed weld, prep the joint, and re-weld with proper penetration. The repair outlasts the rest of the gate in most cases.
Repair vs. Replacement Call
Sometimes a weld repair is a patch on a gate that’s honestly done. We’ll tell you straight if the frame is too far gone or if continued repairs are throwing good money after bad, and we’ll quote a full replacement only when it’s the honest answer.
Commercial Gate Repair
Commercial gate repair in Rowlett covers slide gates, barrier arms, cantilever systems, and high-cycle swing gates at apartment complexes, business parks, HOAs, and industrial sites. Commercial operators run more cycles in a month than a residential gate runs in a year, so the failure math is different. We service commercial-ready brands like DoorKing, Linear, and Viking that are built for that duty cycle. When a commercial gate fails, it’s usually the operator, a damaged V-track, a photo eye, or a control panel issue tied to the access system.
High-Cycle Operator Work
DOORKing and Linear operators are common across Rowlett commercial properties, and we know their control boards, limit logic, and failure patterns. A sticking limit switch or worn gearbox gets diagnosed quickly because we’ve seen those exact units hundreds of times, not because we’re reading a manual for the first time on your dime.
Access Control Integration
A gate operator is one part of a larger access system. We coordinate with the keypads, card readers, and vehicle detection loops already on the property so the gate works with the access system, not against it.
Iron Gate Repair
Iron gate repair covers ornamental iron gates and estate-style driveway gates, the ones where both function and appearance matter. Iron gates rust, rack out of square, and develop loose pickets over time. The most common Rowlett issues we see are rust-through at the bottom rail, sagging from undersized hinges, and broken scrollwork. We repair the structure first, then address the finish, so the gate doesn’t fail again in six months. We work on iron gates from simple single-swing driveway gates to full-width double drives.
Rust and Rot Repair
North Texas humidity plus iron equals rust, especially at the bottom rail where water pools. We cut out the rotted section, weld in a new steel section, and grind the repair smooth before priming and painting. The gate keeps its strength and its look.
Square-Up and Alignment
An iron gate that’s gone trapezoid drags on the ground or won’t latch. We re-square the frame with proper fixtures, then adjust or replace the hinges so the gate carries its load without sagging again in a season or two.
Sliding Gate Repair
Sliding gate repair addresses cantilever and V-track slide gates, common on larger residential lots, ranches, and commercial properties across Rowlett. A sliding gate that jumps the track, binds halfway open, or grinds with every cycle is usually a track problem, a roller problem, or both. We replace worn rollers and guide assemblies, repair or reset V-track, and diagnose the operator if the issue is electrical instead of mechanical. Sliding gates are heavier than swing gates and the repair has to account for that load, not just make the gate move again.
Track and Roller Replacement
Worn rollers on a V-track gate wear the track itself. Replace the rollers early and the track survives; wait too long and you’re re-welding the track. We inspect the full roller assembly, replace the worn components, and check the track gauge so the load is distributed evenly.
Operator Reset and Limit Adjustment
If the gate opens fine but creeps through the close limit or stops short, the issue is often in the operator’s limit settings or the chain tension. We set the limits, tension the chain properly, and verify the stop points, rather than telling you to just “live with it.”
Wrought Iron Gate Repair
Wrought iron gate repair sounds similar to iron gate repair, and the realities are close: it’s ornamental metalwork that has to look right and work right. The difference is usually in the details: twisted pickets, decorative scrollwork, finials, and more delicate sections that need a lighter hand. We repair broken or missing pickets, restore gapped welds on scrollwork, re-hang dropped gates, and match the existing design as closely as the remaining material allows. When the existing work is too far gone to match, we’ll say so up front rather than fabricate something that looks like a patch job.
Scrollwork and Picket Matching
Decorative elements brittle with age snap under load or corrosion. We fabricate replacement sections by hand where possible and weld them in clean, then blend the finish. The repair should be hard to spot, not obvious from the street.
Rehanging and Hardware Upgrade
Many wrought iron gates fail because the original builder undersized the hinges. We replace light-duty hardware with heavier-duty equivalents that carry the actual gate weight, then adjust the gate so it latches and locks cleanly.
Metal Gate Repair
Metal gate repair is the broad category covering steel, aluminum, and tube-frame gates that are structurally sound but have a specific functional failure. A bent section, a bad weld, a loose post, a broken latch, a misaligned receiver. We straighten bent frame members when the metal still has integrity, weld cracks at stress points, reinforce weak sections with proper gussets, and replace hardware that has simply worn out. Metal gates in Rowlett also suffer from thermal movement: summer heat expands the frame, and if the gate was built without clearance, it binds in July, then works fine in January. We account for that when we re-align.
Structural Straightening and Reinforcement
When a vehicle or a wind gust bends a frame member, the gate may still move but the geometry is gone. We straighten the frame cold where possible, add reinforcement where the section has weakened, and realign the gate to remove stress from the operator.
Latch, Lock, and Receiver Repair
A gate that closes but won’t latch is a gate that doesn’t secure anything. We rebuild or replace latches, magnetic locks, drop rods, and receiver posts so the gate actually secures when closed.
Wood Gate Repair
Wood gate repair in Rowlett is a different trade from metal work, but the failure modes are familiar: sagging, rot, and failed hardware. Wood gates are heavy, and weight plus North Texas moisture equals sag. A wooden driveway gate with a rotten lower rail or broken hinge screws needs more than a re-tighten; the old screw holes are stripped and the wood is mush. We scarf in new sections where the damage is localized, or rebuild the gate frame entirely if the rot has spread. Cedar and pressure-treated gates respond differently to repair, and we treat each by what it’s made of.
Rot Repair and Section Replacement
The bottom rail and hinge-side stile rot first because that’s where water sits. We cut out the damaged section and splice in new material with structural joinery, then seal the repair so it doesn’t wick moisture back in.
Anti-Sag Kits and Hardware Rebeds
Every wood gate sags eventually. The fix is either a tensioned anti-sag kit with proper turnbuckle placement, or a full hinge rebed with longer fasteners or through-bolts. We do both and adjust the gate so it latches without lifting.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the brand you already have. That’s one of the biggest reasons Rowlett homeowners and property managers call us instead of a generalist who only stocks one or two product lines. If you’re weighing options, our Choosing the Right Gate Repair Brand: A Buyer’s Guide for Rowlett can help. When you have a Gate Operators from Linear, a Viking swing operator, or a Ghost Controls system running your gate, we know the boards, the wiring, and the failure patterns because we service them regularly.
DoorKing is another one we see a lot on the commercial and HOA side around Rowlett. Their slide gate operators have specific limit-switch and loop-detector wiring that an untrained tech can misdiagnose easily, and misdiagnosis means paying for parts you didn’t need. Whether your operator is Linear, Viking, Ghost Controls, DoorKing, or any other make, we can help.
Signs You Need a Pro Right Now
- The gate stops mid-cycle and won’t reset. A gate that halts halfway and goes into error mode usually has a failing limit switch, a bad photo eye, or a control board issue. Continuing to run it manually or forcing it damages the operator.
- You can hear the motor running but the gate doesn’t move. That’s typically a broken drive chain, a sheared sprocket key, or a stripped gear. The motor is working against nothing, and you’re burning it out while the gate stays stuck.
- The gate sags visibly and scrapes the ground. Hinges are gone or the post is shifting. Every cycle adds more damage to the frame, and if it’s an automated gate, the operator is straining against the extra friction.
- The keypad or remote stopped working without explanation. This could be a dead receiver board, a blown fuse, or an antenna issue. Electrical troubleshooting is safer and faster when you know which board you’re looking at, and gate-control systems carry voltage you shouldn’t guess at.
- You heard a loud crack and the gate now feels “loose.” A weld has likely failed or a hinge pin has sheared. The gate may still move today, but with the load path compromised, it can drop without warning and injure someone or damage a vehicle.
Our Process, Step by Step
- 1
Call and describe what’s happening. We’ll ask specific questions: is it swing or slide, manual or electric, what’s the brand, what’s the symptom. Two minutes on the phone tells us which parts to load and which tech to send.
- 2
We arrive and run a full-system diagnosis. We test the gate manually, check the operator’s error codes, and look at all the moving parts together, not just the one that’s obviously broken. The mechanical and electrical sides affect each other.
- 3
You get an exact repair quote before we touch anything. The price is quoted and agreed before any work starts. If there’s an option between repair and replacement, we’ll lay out both costs honestly and tell you which one we’d choose for our own gate.
- 4
We complete the repair with proper parts. We use original or equivalent-quality parts matched to the gate’s brand and size. No universal brackets hacked in where an OEM part belongs.
- 5
We test the full cycle and walk you through it. Before we leave, we run the gate through open, close, and safety reverse, then show you what was fixed and what to watch for. You should understand the repair, not just see it moving again.
How Much Does Gate Repair Cost in Rowlett?
A typical gate repair in Rowlett runs $150 to $650 for most mechanical fixes, while electrical and operator repairs run $200 to $800 depending on the part and the board. For a deeper breakdown, see our Gate Repair pricing overview. Simple things, like hinge replacement or a photo eye alignment, sit at the lower end of that range. A full operator replacement can run higher, and we’ll quote that before any work starts. The price is always quoted and agreed before work begins, so the invoice doesn’t surprise you.
What moves the price: the gate’s brand and age, whether the repair is mechanical or electrical, and how available the parts are. A specialty control board takes longer to source than a hinge. What keeps it down: calling early. A gate that’s been grinding for six weeks costs more to fix than a gate caught on day three. Our estimates are free, so you can call (877) 265-5743 and know exactly what you’re looking at before committing to anything.
Our Service Area Near Rowlett
Pinehurst Gate Repair serves Rowlett and the communities around it: Rockwall, Heath, Sunnyvale, Wylie, Murphy, Travis Ranch, Saint Paul, Mesquite, Richardson, and both Garland and Sachse. If you’re in any of these areas and your gate has failed, give us a call. We know the neighborhoods, the soil, and the common gate types in each market. Read more about our Gate Repair in Rowlett services or start on the home page for the full scope of what we do.
Serving Rowlett, TX — Our Local Coverage Area
We’re based in the Rowlett area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Rowlett
Gate repair is the process of diagnosing and fixing a gate that has stopped opening, closing, latching, or operating safely. For manual gates, that usually means hinge, post, frame, or latch work. For automated gates, it adds the operator, control board, photo eyes, and access keypads to the picture. We handle both sides, mechanical and electrical.
Most Rowlett gate repairs are completed in a single visit lasting one to three hours. The exceptions are jobs where a part has to be ordered, or a gate has structural damage requiring welding and fabrication on-site. We’ll give you a realistic time estimate when we diagnose the gate, not a vague promise.
Most repairs in Rowlett run between $150 and $800 depending on whether the problem is mechanical or electrical and what brand of operator is involved. The price is quoted upfront and agreed before any work starts, so you won’t get a surprise invoice. Call (877) 265-5743 and we’ll give you a real number, not a range that shifts after we arrive.
Yes, we service gate operators from nine major brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We carry brand-specific diagnostic knowledge and commonly needed parts for these units, so the repair is faster and more accurate. No matter what brand is running your gate, we can work on it.
If your gate is stuck open and can’t be secured, call us at (877) 265-5743 and we’ll prioritize getting a technician to you. A gate that won’t close is a security issue, and we treat it like one. Routine repairs are scheduled at your convenience, but we make room for genuine emergencies.
We stand behind the repairs we complete and we’ll tell you exactly what’s covered before we start. If something related to our repair fails shortly after we leave, we come back and make it right. The terms are spelled out at the time of the estimate, so there’s no asterisk conversation later.
Clear the area around the gate so we have room to work, and if you have a remote or keypad code, have it ready so we can test the operator. If the gate is electric, leave the power to the operator alone; we’ll handle disconnects safely. You don’t need to lift or force anything, and honestly, you shouldn’t.
Schedule Your Gate Repair Service in Rowlett Today
Your gate isn’t going to fix itself, and every cycle it runs while broken is another cycle of damage. Call (877) 265-5743 to schedule a free estimate for gate repair in Rowlett. We’ll diagnose the real problem, quote the repair before any work starts, and get your gate back to secure.