Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Highland Park
When an electric gate fails in Highland Park, it is not a minor inconvenience. A gate stuck open leaves an estate unsecured. A gate stuck shut blocks the driveway and the service alley. We repair both, usually the same day we get the call. Pinehurst Gate Repair works on the gates behind the brick and stone piers along Armstrong Parkway, Lakeside Drive, and the streets around Dallas Country Club. Call (877) 265-5743 and we’ll get a specialist out to your property in Highland Park, 75205.
Why Pinehurst Gate Repair Is Highland Park’s Preferred Electric Gate Repair Company
Highland Park homeowners do not want a generalist knocking on their gate. They want someone who knows the difference between a BFT hydraulic operator and a LiftMaster jackshaft, who can diagnose a dead FAAC control board without swapping parts on a guess, and who respects the fact that the gate has to match the house. That’s what we do. Electric Gate Repair is not a side line for us. It is the entire job. Our team, led by Ronnie Beshears, has hands-on diagnostic experience with nine major gate brands, so when we arrive in Highland Park we know the equipment already. We have re-hung sagging iron gates off Preston Road and replaced water-damaged control boards on alley gates behind Beverly Drive. The work is specific, and so are we.
Highland Park’s housing stock is older than most of Dallas. The estate homes from the 1920s through the 1960s came with masonry piers and custom steel or wrought iron gates that were built before modern UL 325 safety standards existed. When we repair those systems, we are working with the original architecture as much as the operator. That local knowledge means the repair blends in and works correctly the first time.
Styles & brands we work with
Electric Gate Motor in Highland Park
An electric gate motor in Highland Park has a hard life. Summer heat bakes the operator housing. Black clay soil shifts the gate posts and throws the travel alignment off. When the motor strains against a sagging gate for months, it fails. We replace or rebuild gate motors on both swing and slide gates, and a typical motor replacement on a Highland Park estate runs $650 to $1,400 depending on the operator type and whether the control board is integrated. The first thing we do is confirm the gate itself hangs square. Replacing a motor on a gate that still binds against a heaved pier is a waste of a good operator.
Operator Arm and Ram Repairs
Articulated arms on swing gates take the brunt of Highland Park’s spring windstorms. A solid wrought iron gate becomes a sail in 50 mph gusts, and the arm bends or shears at the clevis pin. We carry replacement arms and pins for Viking, Linear, and FAAC operators, so the repair is often done in one visit. The arm is only half the fix. We check the post footing and hinge alignment while we are there, because a bent arm is usually a symptom, not the root cause.
Slide Gate Track and Roller Work
Slide gates are less common on Highland Park driveways but more common on service alleys and estate side entries. Clay soil movement throws V-track out of level. The gate then rides up on the rollers, grinds the chain, and trips the overload on the motor. We re-level track, replace seized rollers, and reset the limit switches. A track repair in Highland Park typically runs $300 to $600, plus any motor work.
Gate Access Control in Highland Park
Gate access control in Highland Park is often a mix of old and new. The estate has a keypad at the main drive, a second keypad or button at the service alley, and maybe a phone-line or cellular intercom for guests. We service the whole chain: keypads, radio receivers, vehicle loop detectors, photo-eyes, and the wiring between them. A keypad replacement on a Highland Park pillar mount runs $250 to $500, and a full access control refresh (new panel, keypad, remote receiver, and programming) runs $800 to $1,500 on a typical two-gate property. The goal is a system where your code opens your gate in bad weather, not just on a clear day.
Keypad and Intercom Upgrades
Highland Park gates sit far from the house. Wireless signals have to travel the length of a long driveway, past masonry piers and mature oaks. When the range drops, we add a remote antenna or upgrade the receiver rather than telling you to stand closer to the gate. Keypads on south-facing piers get sun-baked; the buttons crack and the code pad fails. Replacement is straightforward and we program it on site.
Vehicle Loop Detectors and Exit Wands
Underground loop detectors rot in Highland Park’s clay. The wire insulation cracks as the soil expands and contracts, and the loop stops sensing the car. Exit wands are a cleaner retrofit for older drives where cutting a new loop means tearing up brick pavers. We test loop frequency and replace failed detectors so the gate does not sit open or refuse to close with a car in the way.
Trusted Brands We Service in Highland Park
Your gate already has an operator on it. Our job is to fix that one, not to sell you a different brand because it happens to be what we stock. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so when a FAAC board on a Highland Park driveway loses power or a Linear arm snaps after a storm, we diagnose it from experience rather than guessing at proprietary wiring. We keep common replacement parts and control boards stocked for fast turnaround, and we source the rest from local suppliers in the Dallas area. Manual or electric, swing or slide, we work on the brand you already have.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Highland Park Homes
- Post heave and gate sag: Expansive black clay under Highland Park swells after rain and shrinks in drought. The hinge post moves, the gate sags, and the latch or operator arm binds. We re-plumb the post or shim the hinges to get the gate swinging square again.
- Storm damage to gates and operators: Spring hail and straight-line winds knock solid infill gates out of alignment, bend strike hardware, and yank exposed operator arms. After a storm passes, we reset the travel limits and repair or replace the damaged hardware.
- Photo-eye and safety edge failures on alley gates: Alley service gates behind Highland Park estates sit in deep shade under live oaks and ivy. Moisture gets into the photo-eye housings, debris blocks the beam, and the safety edge degrades. The gate refuses to close, which is exactly what it should do. We replace the sensors and get the gate closing again.
- Aging openers that predate UL 325: Many original Highland Park gate systems were installed before modern entrapment protection was code. When those systems fail, the repair has to bring the safety circuit up to current UL 325 standards, not just restore the old wiring. We handle that as part of the job.
Pricing for Electric Gate Repair in Highland Park, TX
An electric gate repair in Highland Park typically falls between $180 and $400 for service work like photo-eye replacement, limit switch adjustment, or a board swap. Motor and operator replacements run $650 to $1,400 on average depending on the model. Full gate access control refreshes run $800 to $1,500 on a two-gate estate. Heavy steel or custom wrought iron work, post re-plumbing, or matched brick and stone pier repair adds to the total because it requires more labor and materials. We quote the price before any work begins, and you approve it first. No surprises on the invoice. Call (877) 265-5743 for a free estimate at your Highland Park property.
We Also Serve Cities Near Highland Park
Pinehurst Gate Repair is based in Rowlett, but our service area covers Highland Park and the surrounding communities: Dallas, University Park, Richardson, and Farmers Branch. If your property sits near the border of Highland Park and Dallas, or you manage gates across several municipalities, we can help with all of them. One call covers the whole area.
Serving Highland Park, TX — Our Local Coverage Area
We’re based in the Highland Park area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Highland Park
Check the power to the operator first. In Highland Park, storm damage often trips a GFCI outlet or the breaker on the gate circuit, especially after lightning. If the operator has power but the gate will not move, check whether the photo-eye lenses are covered in storm debris or knocked out of alignment. A blocked or misaligned photo-eye will stop the gate from closing. If the gate has power and the eyes are clean but the motor just hums, the gate is likely bound against a shifted post or a bent arm from wind load. That requires a service call: phone (877) 265-5743 and we’ll send a gate specialist to your Highland Park property.
Every automatic gate operator has a manual release. On most LiftMaster and FAAC swing gate operators in Highland Park, there is a keyed release on the side of the operator housing. Insert the key, turn it, and the operator disengages so you can push the gate open by hand. On slide gate operators, the release is usually a lever or pull handle on the motor housing. If your gate has a maglock, the lock also releases when the power drops. Practice the release procedure before you need it, because doing it for the first time in the dark during a storm is difficult. Then call us after the power returns so we can confirm the operator re-engages correctly and the travel limits are intact.
Because the problem is in the ground, not the hinges. In Highland Park, the black clay soil under your gate posts expands and contracts with moisture, and the post itself shifts. The gate then hangs out of plumb and the hinges cannot compensate. Shimming the hinge is a temporary fix. The real repair is re-plumbing the post footing: digging down, setting the post plumb, and re-consolidating the soil or setting it in concrete. We did this on an Armstrong Parkway estate after a hailstorm had heaved the hinge post, and the gate has held square since. If your gate sags again after a hinge adjustment, the post is the problem, and that is a repair we do regularly in Highland Park.
If your Highland Park gate system was installed before the early 2000s, it may not meet current UL 325 entrapment protection standards. UL 325 requires monitored photo-eyes, contact edges or equivalent, and in many cases audio alarms on the operator. Older systems often have no photo-eyes at all, which is a legal and safety risk for a high-traffic driveway. When we repair or replace an operator on an older Highland Park property, we bring the safety circuit up to current UL 325 at the same time. It is not optional. Call (877) 265-5743 and we will test your existing sensors and tell you exactly what needs upgrading.
Yes. Highland Park’s design standards and deed restrictions mean gate repairs have to match the existing estate architecture. We repair and re-plumb brick and stone piers, and we replace or repair wrought iron and steel gate frames without altering the visual character of the entry. When we fixed the custom wrought iron swing gate off Armstrong Parkway, we re-consolidated the lifted pier, corrected the sag, and replaced the damaged safety photocell, leaving the gate looking exactly as it had before the storm. Matching existing work is a normal part of our Highland Park repairs, not an extra project.
When your gate is stuck, sagging, or dead in Highland Park, call the gate specialists. Ronnie Beshears and the Pinehurst Gate Repair team serve the entire 75205 area. Estimates are free, and the price is quoted before any work starts. Call (877) 265-5743.
Written by Ronnie Beshears, Owner at Pinehurst Gate Repair, serving Highland Park and the surrounding Dallas area.